this is my PMDG MD11 lights . Back up you current config file before you use it ! The lighting is great ! I added an extra beacon effect to the belly so I have a beacon glow on the pod engines. Looks cool !
hope you like it .
Add this to MD11 and MD11/F aircraft config files .....
[LIGHTS]
//Types: 1=beacon, 2=strobe, 3=navigation, 4=cockpit, 5=landing, 6=taxi, 7=recognition, 8=wing, 9=Logo
light.0 = 2, -140.80, -85.000, 1.000, Fx_shockwave_strobe, // Shockwave light
light.1 = 2, -140.80, 85.000, 1.000, Fx_shockwave_strobe, // Shockwave light
light.2 = 1, -84.00, 0.00, 11.300, Fx_shockwave_beaconh, // Shockwave light
light.3 = 1, -140.00, 0.00, -9.000, Fx_shockwave_beaconb, // Shockwave light
light.4 = 1, -80.00, 0.00, -8.100, Fx_shockwave_beaconb, // Shockwave light
light.5 = 4, 95.00, -1.50, 5.000, fx_vclightwhi,
light.6 = 4, 95.00, 1.50, 5.000, fx_vclightwhi,
light.7 = 4, 95.50, 0.00, 3.500, fx_vclightwhi,
light.8 = 5, 74.80, -0.90, -8.200, Fx_shockwave_landing_light_light, // Shockwave light - nose gear
light.9 = 5, 74.80, 0.90, -8.200, Fx_shockwave_landing_light_light, // Shockwave light - nose gear
light.10 = 5, -19.500, -8.50, -3.750, Fx_shockwave_landing_light, // Shockwave light
light.11 = 5, -19.500, 8.50, -3.750, Fx_shockwave_landing_light, // Shockwave light
light.12 = 5, 3.500, -2.00, -8.750, Fx_shockwave_landing_light_light, // Shockwave light
light.13 = 5, 3.500, 2.00, -8.750, Fx_shockwave_landing_light_light, // Shockwave light
light.14 = 8, -85.231, 23.611, -1.000, fx_PMDG_MD11_winglight,
light.15 = 7, -85.231, -23.611, -1.000, fx_PMDG_MD11_winglight,
light.16 = 9, -7.025, 0.00, 4.263, fx_PMDG_MD11_emerlights,
and dont forget to add this line to your panel config ( md11F uses the same panel config as the standard MD11 so you only need to update the one )
Add the following line at the bottom of the [VCockpit01]
section changing 'XX' to the next available number
gaugeXX=shockwave_lights!SW Lights, 1,1,1,1 //shockwave light
IF YA LIKE IT !! LEAVE ME A REPLY AND LET ME KNOW ! just thought it would be nice to have an easy setup for others !!
PMDG MD11 & MD11/F shockwave lighting Config
Re: PMDG MD11 & MD11/F shockwave lighting Config
Thanks a lot for the post, helped a lot.
But I ran into a little problem (FS X). When on ground with High-INT OFF and Taxi Light on the strobe lights come up. When switching the strobes ON then another version (probably the original, not the Shockwave) come on but with less intensity.
Any idea?
But I ran into a little problem (FS X). When on ground with High-INT OFF and Taxi Light on the strobe lights come up. When switching the strobes ON then another version (probably the original, not the Shockwave) come on but with less intensity.
Any idea?
-
- Airman
- Posts: 13
- Joined: 10 Apr 2011, 05:12
Re: PMDG MD11 & MD11/F shockwave lighting Config
I just purchased the full A2A Shockwave redux pack for FSX and FS2004. I have a problem with the fs2004 version payware aircraft. Since there's no FS2004 Shockwave Redux forum, I have no choice but to post here, as I cannot find any way to start a new thread in a forum that doesn't exist.
Firstly, many thanks for the FSX version of the PMDG MD11/MD11F. I simply cannot find anything (I searched and searched ad-infinitum) that helps me to install them into the FS9 version of the PMDG MD11/MD11F (my fs2004 PMDG 747 has them and they're beautiful). I noticed the MD11 aircraft cfg in the FS9 version has very few lights compared to the FSX version. Here's my existing FS9 PMDG MD11 (I can figure that out the "F" version once I get help in the non freighter version) cfg:
PLEASE NOTE BELOW IS IS MY NON-MODIFIED CONFIG - I still need help putting in the 3D lights!
[LIGHTS]
//Types: 1=beacon, 2=strobes, 3=Navigation, 4=Cockpit, 5=landing, 6=taxi, 7=recognition, 8=wing, 9=Logo
light.0 = 8, -85.231, 23.611, -1.000, fx_PMDG_MD11_winglight,
light.1 = 7, -85.231, -23.611, -1.000, fx_PMDG_MD11_winglight,
light.2 = 2, -14.500, 0.00, -10.750, fx_PMDG_MD11_LL_Light,
light.3 = 9, -7.025, 0.00, 4.263, fx_PMDG_MD11_emerlights,
Thanks to anyone that can assist me with this project.
Best regards,
Bill
Firstly, many thanks for the FSX version of the PMDG MD11/MD11F. I simply cannot find anything (I searched and searched ad-infinitum) that helps me to install them into the FS9 version of the PMDG MD11/MD11F (my fs2004 PMDG 747 has them and they're beautiful). I noticed the MD11 aircraft cfg in the FS9 version has very few lights compared to the FSX version. Here's my existing FS9 PMDG MD11 (I can figure that out the "F" version once I get help in the non freighter version) cfg:
PLEASE NOTE BELOW IS IS MY NON-MODIFIED CONFIG - I still need help putting in the 3D lights!
[LIGHTS]
//Types: 1=beacon, 2=strobes, 3=Navigation, 4=Cockpit, 5=landing, 6=taxi, 7=recognition, 8=wing, 9=Logo
light.0 = 8, -85.231, 23.611, -1.000, fx_PMDG_MD11_winglight,
light.1 = 7, -85.231, -23.611, -1.000, fx_PMDG_MD11_winglight,
light.2 = 2, -14.500, 0.00, -10.750, fx_PMDG_MD11_LL_Light,
light.3 = 9, -7.025, 0.00, 4.263, fx_PMDG_MD11_emerlights,
Thanks to anyone that can assist me with this project.
Best regards,
Bill
Re: PMDG MD11 & MD11/F shockwave lighting Config
[LIGHTS]
//Types: 1=beacon, 2=strobe, 3=navigation, 4=cockpit, 5=landing, 6=taxi, 7=recognition, 8=wing, 9=Logo
light.0 = 8, -85.231, 23.611, -1.000, fx_PMDG_MD11_winglight,
light.1 = 7, -85.231, -23.611, -1.000, fx_PMDG_MD11_winglight,
light.2 = 9, -7.025, 0.00, 4.263, fx_PMDG_MD11_emerlights,
light.3 = 1, -84.420, 0.00, 11.200, fx_shockwave_beaconh
light.4 = 1, -138.850, 0.00, -8.900, fx_shockwave_beaconb
light.5 = 8, -20.100, 8.10, -3.300, Fx_shockwave_landing_light_small_xenon // ShockWave light
light.6 = 8, -20.100, -8.10, -3.300, Fx_shockwave_landing_light_small_xenon // ShockWave light
light.7 = 0, -140.80, -85.000, 1.000, Fx_shockwave_strobe, // ShockWave light
light.8 = 0, -140.80, 85.000, 1.000, Fx_shockwave_strobe, // ShockWave light
I still have 7 and 8 set to 0 because I am still trying to figure out how to set the strobes with the correct key.
//Types: 1=beacon, 2=strobe, 3=navigation, 4=cockpit, 5=landing, 6=taxi, 7=recognition, 8=wing, 9=Logo
light.0 = 8, -85.231, 23.611, -1.000, fx_PMDG_MD11_winglight,
light.1 = 7, -85.231, -23.611, -1.000, fx_PMDG_MD11_winglight,
light.2 = 9, -7.025, 0.00, 4.263, fx_PMDG_MD11_emerlights,
light.3 = 1, -84.420, 0.00, 11.200, fx_shockwave_beaconh
light.4 = 1, -138.850, 0.00, -8.900, fx_shockwave_beaconb
light.5 = 8, -20.100, 8.10, -3.300, Fx_shockwave_landing_light_small_xenon // ShockWave light
light.6 = 8, -20.100, -8.10, -3.300, Fx_shockwave_landing_light_small_xenon // ShockWave light
light.7 = 0, -140.80, -85.000, 1.000, Fx_shockwave_strobe, // ShockWave light
light.8 = 0, -140.80, 85.000, 1.000, Fx_shockwave_strobe, // ShockWave light
I still have 7 and 8 set to 0 because I am still trying to figure out how to set the strobes with the correct key.
-
- Airman
- Posts: 13
- Joined: 10 Apr 2011, 05:12
Re: PMDG MD11 & MD11/F shockwave lighting Config
Hey Thanks UPS!
Who is online
Users browsing this forum: No registered users and 29 guests