The A2A Simulations Community

In reference to the above light install data for the Convair CV-240, the following applies to change some of the light events:

For those that want the wing landing lights to stay on after the landing gear is raised, and want the taxi light to go out automatically when the landing gear is raised, substitute the following in place of the above lines for "gauge 33 and 34:" Backup this CFG file first - then:[/b][/b]

Add "//" in front of gauge33 line above or delete the line entirely. This line controls the status of the wind landing lights after the gear is raised.

Replace gauge34 line altogether with the following line:

gauge33=shockwave_lights!SW Lights_taxi_gear, 1,1,1,1 //shockwave light

The renumbering of the gauge numbers has already been taken care of in the replacement line. Now you have a choice of events!

bytes

Aeroworx B200 v.2


Add to your Aircraft.cfg file:

[lights]

light.0 = 3, 0.54, -27.34, 3.21, fx_shockwave_navred
light.1 = 1, -5.35, 0, -0.31, fx_shockwave_beaconb
light.2 = 3, 0.54, 27.34, 3.21, fx_shockwave_navgre
light.3 = 2, 0.84, -27.01, 3.19, fx_shockwave_strobe
light.4 = 2, 0.84, 27.01, 3.19, fx_shockwave_strobe_3
light.5 = 1, -24.23, -0.14, 12.53, fx_shockwave_navwhi
light.6 = 4, 5.520, 1.200, 4.495, fx_awxb200_cp
light.7 = 4, 5.520, -1.200, 4.495, fx_awxb200_pic
light.8 = 10, -1.60, 0, 4.49, fx_awxb200_cabf
light.9 = 10, 2.15, 0, 4.49, fx_awxb200_cabm
light.10 = 10, -4.10, 0, 4.49, fx_awxb200_cabb
light.11 = 9, -23.55, -1.0, 6.55, fx_awxb200_logo
light.12 = 9, -23.55, 1.0, 6.55, fx_awxb200_logo
light.13 = 5, 14.90, 0.00, 0.10, fx_shockwave_landing_light_double_small // Double Landing Light
light.14 = 6, 14.90, 0.00, -0.40, fx_shockwave_landing_light_small // Taxi Light


Add to your Panel.cfg file:

[VCockpit01]
gauge01=shockwave_lights!SW Lights_gear, 1,1,1,1 //shockwave light

Stratojet Merlin (Heyart) (FS9)
[lights]
//Types: 1=beacon, 2=strobe, 3=navigation, 4=cockpit, 5=landing, 6=Taxi
light.0 = 3, -12.46, 20.57, 0.6, fx_shockwave_navgre
light.1 = 3, -12.46, -20.57, 0.6, fx_shockwave_navred
light.2 = 3, -11.58, 0, -2.09, fx_shockwave_navwhi
light.3 = 2, -13.2, 20.57, 0.6, fx_shockwave_strobe_nl_2
light.4 = 1, -4.73, 0, 2.55, fx_shockwave_beaconb_nl
light.5 = 1, -2.43, 0, -3.00, fx_shockwave_beaconb_nl
light.6 = 2, -13.2, -20.57, 0.6, fx_shockwave_strobe_nl_3
light.7 = 4, 8.22, 0, 0.45, fx_shockwave_vclight
light.8 = 4, 5.19, 0, 0.42, fx_shockwave_vclight
light.9 = 5, 20, 0, -1.45, fx_shockwave_landing_light_narrow
light.10 = 6, 12.5, 0, -3.90, fx_shockwave_landing_light_low_old

Alphasim Boeing C-17A Globemaster III

[lights]
//Types: 1=beacon, 2=strobe, 3=navigation, 4=cockpit, 5=landing
light.0 = 3, -84.50, 0.0, 13.14, fx_navwhih ; Nav tail
light.1 = 3, -18.85, -84.50, 3.07, fx_navredh ; Nav red
light.2 = 3, -18.85, 84.50, 3.07, fx_navgreh ; Nav grn
light.3 = 1, -85.85, 0.0, 46.00, fx_shockwave_beacon_rotating_red ; Beacon top
light.4 = 1, 27.39, 0.0, -9.90, fx_shockwave_beacon_rotating_red ; Beacon lower
light.5 = 4, 62.71, -2.17, 4.73, fx_vclight ; Cockpit
light.6 = 4, 62.71, 2.17, 4.73, fx_vclight ; Cockpit
light.7 = 2, -18.93, -84.60, 3.07, fx_shockwave_strobe ; Wingtip strobe left fwd
light.8 = 2, -18.93, 84.60, 3.07, fx_shockwave_strobe ; Wingtip strobe right fwd
light.9 = 2, -29.35, -84.60, 3.07, fx_shockwave_strobe ; Wingtip strobe left aft
light.10 = 2, -29.35, 84.60, 3.07, fx_shockwave_strobe ; Wingtip strobe right aft
light.11 = 5, 43.10, -10.90, -3.15, fx_shockwave_landing_light_narrow ; Landing light left
light.12 = 5, 43.10, 10.90, -3.15, fx_shockwave_landing_light_narrow ; Landing light right

Alphasim C-17A Globemaster III

I want to compliment the work of the previous post author and add that in this version I've used all Shockwave light effects as well as adding the two additional Taxi/Landing lights located on the outside wing tips.

[lights]
//Types: 1=beacon, 2=strobe, 3=navigation, 4=cockpit, 5=landing,
light.0 = 3, -84.50, 0.0, 13.14, fx_shockwave_navwhi ; Nav Tail WHite
light.1 = 3, -18.85, -84.50, 3.07, fx_shockwave_navred ; Nav Red Left
light.2 = 3, -18.85, 84.50, 3.07, fx_shockwave_navgre ; Nav Green Right
light.3 = 1, -85.85, 0.0, 46.00, fx_shockwave_beaconh_l ; Nav Beacon Top
light.4 = 1, 27.39, 0.0, -10.15, fx_shockwave_beaconb_l ; Nav Beacon Lower
light.5 = 4, 62.71, -2.17, 4.73, fx_vclight ; Cockpit Lighting
light.6 = 4, 62.71, 2.17, 4.73, fx_vclight ; Cockpit Lighting
light.7 = 2, -18.93, -84.60, 3.07, fx_shockwave_strobe_l ; Wingtip Strobe Left FWD
light.8 = 2, -18.93, 84.60, 3.07, fx_shockwave_strobe_l ; Wingtip Strobe Right FWD
light.9 = 2, -29.35, -84.60, 3.07, fx_shockwave_strobe_l ; Wingtip Strobe Left AFT
light.10 = 2, -29.35, 84.60, 3.07, fx_shockwave_strobe_l ; Wingtip Strobe Right AFT
light.11 = 5, 43.10, -10.90, -3.15, fx_shockwave_landing_light_small_xenon ; Landing Light Left Fuselage
light.12 = 5, 43.10, 10.90, -3.15, fx_shockwave_landing_light_small_xenon ; Landing Light Right Fuselage
light.13 = 5, -17.50, -84.50, 3.07, fx_shockwave_landing_light_small_xenon ; Landing Light Left Wing Tip
light.14 = 5, -17.50, 84.50, 3.07, fx_shockwave_landing_light_small_xenon ; Landing Light Right Wing Tip

Note: If you find that you prefer smaller strobe effects (I used the larger ones), just delete the, "_l" part after each effect name.. e.g. From this: fx_shockwave_strobe_l To this: fx_shockwave_strobe

Kodiak Quest
[Vcockpit01] Add gauge09=shockwave_lights!SW Lights, 1,1,1,1 //shockwave light

[LIGHTS]
//Types: 1=beacon, 2=strobe, 3=navigation, 4=cockpit, 5=landing, 6=Taxi, 7=Recognition,

8=Wing, 9=Logo, 10=Cabin,
light.0 = 3, -0.80, -22.30, 2.89, Fx_shockwave_navred //fx_navred
light.1 = 3, -0.80, 22.30, 2.89, Fx_shockwave_navgre //fx_navgre
light.2 = 3, -9.01, 0, 2.72, fx_shockwave_navwhi_l //fx_navwhi
light.3 = 2, -0.86, -22.30, 2.89, fx_shockwave_strobe //fx_strobe
light.4 = 2, -0.86, 22.30, 2.89, fx_shockwave_strobe //fx_strobe
light.5 = 1, -9.01, 0, 2.72, fx_shockwave_beaconh //fx_beacon
light.6 = 5, 0.87, 20.90, 2.87, fx_Shockwave_landing_light_small //fx_landing
light.7 = 5, 0.83, -20.90, 2.87, fx_Shockwave_landing_light_small //fx_landing
light.8 = 7, 2.60, 0.00, 1.00, fx_vclight,
light.9 = 8, -2.0, 0.00, 2.50, fx_vclight,
light.10 = 8, -7.0, 0.00, 2.50, fx_vclight,
light.11 = 3, -20.26, 0, 1.94, fx_shockwave_navwhi_l //fx_navwhi
light.12 = 12, 0, 0, 1.94, fx_Kodiak_propblast

Content deleted by the author.

Scott, could you please delete this thread? Thanks in advance.

SweetApple_MC

SibWings L-19/O-1 Bird Dog

Add to panel.cfg:

[VCockpit01]
gauge05=shockwave_lights!SW Lights, 1,1,1,1 //shockwave light



Add to aircraft.cfg:

[LIGHTS]
light.0 = 9, 1, 2, 1.45, fx_O1_vclighth_1
light.1 = 8, -2.5, 0, 1, fx_O1_vclighth_2
light.2 = 3, 0.32, -18.2, 3.2, fx_shockwave_navred // Shockwave light
light.3 = 3, 0.32, 18.2, 3.2, fx_shockwave_navgre // Shockwave light
light.4 = 5, 2, -12.3, 3, fx_shockwave_landing_light_low_old // Shockwave light
light.5 = 1, 0.7, -0.017, -2.2, fx_shockwave_beacon_rotating_red // Shockwave light

RealAir Duke

PANEL.cfg

gauge13=shockwave_lights!SW Lights_taxi_gear, 1,1,1,1 //shockwave light
gauge14=shockwave_lights!SW Lights_gear, 1,1,1,1 //shockwave light

If you add one of lines above or both, there is problem with NAV and BCN switch - dosen't work anymore.

AIRCRAFT.cfg

[LIGHTS]
//Types: 1=beacon, 2=strobe, 3=navigation, 4=cockpit, 5=landing, 6=Taxi, 7=Recognition, 8=wing, 9=logo, 10=cabin
light.0 = 3, -6.60, -19.70, 1.01, fx_shockwave_navred
light.1 = 3, -6.60, 19.70, 1.01, fx_shockwave_navgre
light.2 = 3, -26.50, 0.00, 2.20, fx_shockwave_navwhi
light.3 = 2, -6.20, -19.66, 1.01, fx_shockwave_strobe
light.4 = 2, -6.20, 19.66, 1.01, fx_shockwave_strobe
light.5 = 1, -27.68, -0.01, 8.90, fx_shockwave_beacon
light.6 = 7, -7.42, 1.944, -1.69, RASDuke_Recogn
light.7 = 10, -7.80, 0.00, 1.50, RASDuke_vclight
light.8 = 8, -6.20, -13.20, 1.03, RASDuke_wing //de-icing Boots left wing
light.9 = 8, -6.20, 13.20, 1.03, RASDuke_wing //de-icing boots right wing
light.10 = 5, -6.6, -4.7, -1.5, fx_Shockwave_landing_light_short // Shockwave light
light.11 = 5, -6.6, 4.7, -1.5, fx_Shockwave_landing_light_short // Shockwave light
light.12 = 6, 2.0, -0.5, -1.7, fx_Shockwave_landing_light_short // Shockwave light

Carenado Cessna 185 Skywagon

Add to panel.cfg:

[VCockpit01]
gauge09=shockwave_lights!SW Lights, 1,1,1,1 //shockwave light


Add to aircraft.cfg:

[LIGHTS]
//Types: 1=beacon, 2=strobe, 3=navigation, 4=cockpit, 5=landing, 6=taxi
light.0 = 3, -0.36, -16.81, 3.34, fx_shockwave_navred // Shockwave light
light.1 = 3, -0.38, 16.81, 3.36, fx_shockwave_navgre // Shockwave light
light.2 = 3, -16.74, 0.0, 1.3, fx_navwhi85
light.3 = 1, -14.05, 0.04, 6.5, fx_shockwave_beacon_rotating_red // Shockwave light
light.4 = 10, -0.9, 0.0, 1.2, fx_vclightc185
light.5 = 10, -3.7,0.0,2.3, fx_vclightc1852
light.6 = 5, 6.3, -0.8, 0, fx_shockwave_landing_light_low_old // Shockwave light
light.7 = 6, 5.9, 0.8, 0, fx_shockwave_landing_light_small_old // Shockwave light

Hey everyone, does anyone have the config for the Quality Wings 757-200/300 please?
Thanks

Hello,
I am using the pss 777 light config found on the 3rd party list, but I am having a problem with the flex wing setting. When the wings lift, the lights stay in the take off position. Here is a copy of my lights, I have disabled the ones giving me a fit.


[LIGHTS]
//Types: 1=beacon, 2=strobes, 3=Navigation, 4=Cockpit, 5=landing, 6=taxi, 7=recognition, 8=wing, 9=Logo
//light.0 = 3, -32.20, 104.80, 4.00, fx_shockwave_navgre ,
//light.1 = 3, -32.20, -104.80, 4.00, fx_shockwave_navred ,
//light.2 = 2, -35.1, -104.80, 4.00, fx_shockwave_strobe ,
//light.3 = 2, -35.1, 104.80, 4.00, fx_shockwave_strobe ,
//light.4 = 3, -37.7, -104.80, 4.00, fx_shockwave_navwhi ,
//light.5 = 3, -37.7, 104.80, 4.00, fx_shockwave_navwhi ,
light.6 = 1, 49.5, 0, 13.2, fx_shockwave_beacon ,
light.7 = 1, 3.5, 0, -7.8, fx_shockwave_beacon ,
light.8 = 5, 34.2, 12.7, -2.5, fx_shockwave_landing_light ,
light.9 = 5, 34.2, -12.7, -2.5, fx_shockwave_landing_light ,
light.10 = 6, 87.7, 0, -11, fx_shockwave_landing_light_double ,
light.11 = 6, 87.7, 0, -12.5, fx_shockwave_landing_light_double ,


Thanks for any help!


Denny

somebody have the 3d lights for the Dreamwings Fokker 50 Version 3 ?

Captain Sim 727-100

[LIGHTS]
light.0 = 3, -27.59, -52.90, -2.49, fx_shockwave_navred
light.1 = 3, -27.59, 52.90, -2.49, fx_shockwave_navgre
light.2 = 3, -29.00, -53.40, -2.49, fx_shockwave_navred
light.3 = 3, -29.00, 53.40, -2.49, fx_shockwave_navgre
light.4 = 2, -33.50, -53.10, -2.50, fx_shockwave_navwhi
light.5 = 2, -33.50, 53.10, -2.50, fx_shockwave_navwhi
light.6 = 2, -28.25, -53.15, -2.49, fx_shockwave_strobe
light.7 = 2, -28.25, 53.15, -2.49, fx_shockwave_strobe
light.8 = 2, 23.40, 0.00, 7.20, fx_shockwave_beaconh
light.9 = 2, 1.05, 0.00, -7.20, fx_shockwave_beaconh
light.10 = 4, 50.00, -2.50, 0.70, cs727_vclight
light.11 = 4, 48.50, 0.00, 1.00, cs727_vclight
light.12 = 5, 9.50, 6.10, -2.90, fx_Shockwave_landing_light // Shockwave light
light.13 = 5, 9.50, -6.10, -2.90, fx_Shockwave_landing_light // Shockwave light
light.14 = 9, -20.00, -52.00, -4.50, cs727_voda
light.15 = 9, -20.00, 52.00, -4.50, cs727_voda

Captain Sim 727-200

[LIGHTS]
light.0 = 3, -27.59, -52.90, -2.49, fx_shockwave_navred
light.1 = 3, -27.59, 52.90, -2.49, fx_shockwave_navgre
light.2 = 3, -29.00, -53.40, -2.49, fx_shockwave_navred
light.3 = 3, -29.00, 53.40, -2.49, fx_shockwave_navgre
light.4 = 2, -33.50, -53.10, -2.50, fx_shockwave_navwhi
light.5 = 2, -33.50, 53.10, -2.50, fx_shockwave_navwhi
light.6 = 2, -28.25, -53.15, -2.49, fx_shockwave_strobe
light.7 = 2, -28.25, 53.15, -2.49, fx_shockwave_strobe
light.8 = 2, 35.00, 0.00, 7.20, fx_shockwave_beaconh
light.9 = 2, 1.05, 0.00, -7.20, fx_shockwave_beaconh
light.10 = 4, 60.00, -2.50, 0.70, cs727_vclight
light.11 = 4, 58.50, 0.00, 1.00, cs727_vclight
light.12 = 5, 10.0, 6.0, -3, fx_Shockwave_landing_light // Shockwave light
light.13 = 5, 10.0, -6.0, -3, fx_Shockwave_landing_light // Shockwave light
light.14 = 9, -20.00, -52.00, -4.50, cs727_voda
light.15 = 9, -20.00, 52.00, -4.50, cs727_voda